2023年全國碩士研究生考試考研英語一試題真題(含答案詳解+作文范文)_第1頁
已閱讀1頁,還剩19頁未讀, 繼續免費閱讀

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、CHAPTER SIXConducted Emissions and SusceptibilityIn this chapter we will investigate the mechanism by which emissions are generated and are conducted out of the product along the product’s ac power cord. Regulatory agenc

2、ies impose limits on these conducted emissions because they are placed on the commercial power system net of the installation. The commercial power distribution system in an installation is a large array of wires connect

3、ing the various power outlets from which the other electronic systems in the installation receive their ac power. It therefore represents a large “antenna” system from which these conducted emissions can radiate quite ef

4、ficiently, causing interference in the other electronic systems of the installation. Thus the conducted emissions may cause radiated emis- sion, which may then cause interference. Ordinarily, the reduction of these con-

5、ducted emissions is somewhat simpler than the reduction of radiated emissions since there is only one path for these emissions that needs to be controlled: the unit’s power cord. However, it is important to realize that

6、if a product fails to comply with the limits on conducted emissions, compliance with the limits on radiated emissions is a moot point! Therefore controlling conducted emissions of a product has equal priority with the co

7、ntrol of radiated emissions. Once again, manufacturers of electronic products realize that simply complying with the regulatory limits on conducted and radiated emissions does not represent a complete design from the sta

8、ndpoint of EMC. A product must be reasonably insen- sitive to disturbances that are present on the power system net in order to ensure reliable operation of the product. For example, lightning may strike the power trans-

9、 mission lines that feed power to the installation. This may cause disturbances that range from a complete loss of commercial power (which no product is expected to withstand) to momentary power loss due to power system

10、circuit breakers attempting to reclose (which a product is expected to withstand without loss ofIntroduction to Electromagnetic Compatibility, Second Edition, by Clayton R. Paul Copyright # 2006 John Wiley & Sons, In

11、c.136.1.1 The Line Impedance Stabilization Network (LISN)The purpose of the conducted emission test is to measure the noise currents that exit the product’s ac power cord conductors. These emissions could be simply measu

12、red with a current probe. However, the requirement that the measured data be correla- table between measurement sites may render this simple test unrealistic. The impe- dance seen looking into the ac power system wall ou

13、tlets varies considerably over the measurement frequency range and from outlet to outlet and building to building [1]. This variability in the loading presented to the product affects the amount of noise that is conducte

14、d out the power cord. In order to make this consistent between test sites, the impedance seen by the product looking out the product’s ac power cord must be stabilized from measurement site to measurement site. This is t

15、he first objective of the LISN—to present a constant impedance to the pro- duct’s power cord outlet over the frequency range of the conducted emission test. Also, the amount of noise that is present on the power system n

16、et varies from site to site. This “external” noise enters the product’s ac power cord, and, unless it is somehow excluded, will add to the measured conducted emissions. It is desired to measure only those conducted emiss

17、ions that are due to the product, and this gives the second objective of the LISN—to block conducted emissions that are not due to the product being tested so that only the conducted emissions of the product are measured

18、. Therefore the two objectives of the LISN are (1) to present a constant impedance (50 V) between the phase conductor and the safety wire (the “green wire”) and between the neutral conductor and the safety wire, and (2)

19、to prevent external conducted noise on the power system net from contami- nating the measurement. These two objectives are to be satisfied only over the fre- quency range of the conducted emission test (150 kHz–30 MHz).

20、Another subtle but unstated requirement for the LISN is that it be able to pass the 60 Hz (50 Hz) power required for operation of the product. The LISN specified for use in the conducted emission measurement is shown in

21、Fig. 6.2. The purpose of the 1 mF capacitors between phase and green wire and between neutral and green wire on the commercial power side is to divert “external noise” on the commercial power net and prevent that noise f

22、rom flowing through the measurement device and contaminating the test data. Similarly, the purpose of the 50-mH inductors is to block that noise. The purpose of the other 0.1-mF capacitors is to prevent any dc from overl

23、oading the input of the test receiver. It is instructive to compute the impedances of these elements at the lower frequency limit, 150 kHz, and the upper frequency limit, 30 MHz, of the FCC regulatory limit. These areEle

24、ment Z150 kHz Z30 MHz50 mH 47.1 V 9424.8 V 0.1 mF 10.61 V 0.053 V 1 mF 1.06 V 0.0053 VThus the capacitors are low impedances over the measurement frequency range, and the inductor presents a large impedance. The 1-kV res

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 眾賞文庫僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

評論

0/150

提交評論