數控車床畢業設計外文翻譯--車床

1、<p><b>　　Lathes</b></p><p>　　Lathes are machine tools designed primarily to do turning, facing and boring, Very little turning is done on other types of machine tools, and none can do it wit

2、h equal facility. Because lathes also can do drilling and reaming, their versatility permits several operations to be done with a single setup of the work piece. Consequently, more lathes of various types are used in man

3、ufacturing than any other machine tool.</p><p>　　The essential components of a lathe are the bed, headstock assembly, tailstock assembly, and the leads crew and feed rod.</p><p>　　The bed is the

4、 backbone of a lathe. It usually is made of well normalized or aged gray or nodular cast iron and provides s heavy, rigid frame on which all the other basic components are mounted. Two sets of parallel, longitudinal ways

5、, inner and outer, are contained on the bed, usually on the upper side. Some makers use an inverted V-shape for all four ways, whereas others utilize one inverted V and one flat way in one or both sets, They are precisio

6、n-machined to assure accuracy of alignment. On</p><p>　　The headstock is mounted in a foxed position on the inner ways, usually at the left end of the bed. It provides a powered means of rotating the word at

7、 various speeds . Essentially, it consists of a hollow spindle, mounted in accurate bearings, and a set of transmission gears-similar to a truck transmission—through which the spindle can be rotated at a number of speeds

8、. Most lathes provide from 8 to 18 speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained mere</p><p>　　Because the accuracy of a lathe is greatly dependent on the spindle,

9、 it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. The spindle has a hole extending through its length, through which long bar stock can be fed. The size of maximu

10、m size of bar stock that can be machined when the material must be fed through spindle.</p><p>　　The tailsticd assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the be

11、d and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location, An upper casting fits on the lower one and can be moved transversely upon it, on some type of keyed ways, to

12、permit aligning the assembly is the tailstock quill. This is a hollow steel cylinder, usually about 51 to 76mm(2to 3 inches) in diameter, that can be moved several inches</p><p>　　The size of a lathe is desi

13、gnated by two dimensions. The first is known as the swing. This is the maximum diameter of work that can be rotated on a lathe. It is approximately twice the distance between the line connecting the lathe centers and the

14、 nearest point on the ways, The second size dimension is the maximum distance between centers. The swing thus indicates the maximum work piece diameter that can be turned in the lathe, while the distance between centers

15、indicates the maximum length of w</p><p>　　Engine lathes are the type most frequently used in manufacturing. They are heavy-duty machine tools with all the components described previously and have power driv

16、e for all tool movements except on the compound rest. They commonly range in size from 305 to 610 mm(12 to 24 inches)swing and from 610 to 1219 mm(24 to 48 inches) center distances, but swings up to 1270 mm(50 inches) an

17、d center distances up to 3658mm(12 feet) are not uncommon. Most have chip pans and a built-in coolant circulating sy</p><p>　　Although engine lathes are versatile and very useful, because of the time require

18、d for changing and setting tools and for making measurements on the work piece, thy are not suitable for quantity production. Often the actual chip-production tine is less than 30% of the total cycle time. In addition, a

19、 skilled machinist is required for all the operations, and such persons are costly and often in short supply. However, much of the operator’s time is consumed by simple, repetitious adjustments and i</p><p>

20、　　2 Numerical Control</p><p>　　One of the most fundamental concepts in the area of advanced manufacturing technologies is numerical control (NC). Prior to the advent of NC, all machine tools ere manually ope

21、rated and controlled. Among the many limitations associated with manual control machine tools, perhaps none is more prominent than the limitation of operator skills. With manual control, the quality of the product is dir

22、ectly related to and limited to the skills of the operator. Numerical control represents the first major</p><p>　　Numerical control means the control of machine tools and other manufacturing systems through

23、the use of prerecorded, written symbolic instructions. Rather than operating a machine tool, an NC technician writes a program that issues operational instructions to the machine tool. For a machine tool to be numericall

24、y controlled, it must be interfaced with a device for accepting and decoding the programmed instructions, known as a reader.</p><p>　　Numerical control was developed to overcome the limitation of human opera

25、tors, and it has done so. Numerical control machines are more accurate than manually operated machines, they can produce parts more uniformly, they are faster, and the long-run tooling costs are lower. The development of

26、 NC led to the development of several other innovations in manufacturing technology: </p><p>　　Electrical discharge machining,Laser cutting,Electron beam welding.</p><p>　　Numerical control has

27、also made machine tools more versatile than their manually operated predecessors. An NC machine tool can automatically produce a wide of parts, each involving an assortment of widely varied and complex machining processe

28、s. Numerical control has allowed manufacturers to undertake the production of products that would not have been feasible from an economic perspective using manually controlled machine tolls and processes.</p><

29、p>　　Like so many advanced technologies, NC was born in the laboratories of the Massachusetts Institute of Technology. The concept of NC was developed in the early 1950s with funding provided by the U.S. Air Force. In

30、its earliest stages, NC machines were able to made straight cuts efficiently and effectively. </p><p>　　However, curved paths were a problem because the machine tool had to be programmed to undertake a serie

31、s of horizontal and vertical steps to produce a curve. The shorter the straight lines making up the steps, the smoother is the curve, Each line segment in the steps had to be calculated. </p><p>　　This probl

32、em led to the development in 1959 of the Automatically Programmed Tools (APT) language. This is a special programming language for NC that uses statements similar to English language to define the part geometry, describe

33、 the cutting tool configuration, and specify the necessary motions. The development of the APT language was a major step forward in the fur ther development from those used today. The machines had hardwired logic circuit

34、s. The instructional programs were written on punc</p><p>　　A major problem was the fragility of the punched paper tape medium. It was common for the paper tape containing the programmed instructions to brea

35、k or tear during a machining process. This problem was exacerbated by the fact that each successive time a part was produced on a machine tool, the paper tape carrying the programmed instructions had to be rerun through

36、the reader. If it was necessary to produce 100 copies of a given part, it was also necessary to run the paper tape through the reader</p><p>　　This led to the development of a special magnetic plastic tape.

37、Whereas the paper carried the programmed instructions as a series of holes punched in the tape, the plastic tape carried the instructions as a series of magnetic dots. The plastic tape was much stronger than the paper ta

38、pe, which solved the problem of frequent tearing and breakage. However, it still left two other problems. </p><p>　　The most important of these was that it was difficult or impossible to change the instructi

39、ons entered on the tape. To made even the most minor adjustments in a program of instructions, it was necessary to interrupt machining operations and make a new tape. It was also still necessary to run the tape through t

40、he reader as many times as there were parts to be produced. Fortunately, computer technology became a reality and soon solved the problems of NC associated with punched paper and plastic ta</p><p>　　The deve

41、lopment of a concept known as direct numerical control (DNC) solved the paper and plastic tape problems associated with numerical control by simply eliminating tape as the medium for carrying the programmed instructions.

42、 In direct numerical control, machine tools are tied, via a data transmission link, to a host computer. Programs for operating the machine tools are stored in the host computer and fed to the machine tool an needed via t

43、he data transmission linkage. Direct numerical contr</p><p><b>　　3 Turning</b></p><p>　　The engine lathe, one of the oldest metal removal machines, has a number of useful and highly

44、desirable attributes. Today these lathes are used primarily in small shops where smaller quantities rather than large production runs are encountered.</p><p>　　The engine lathe has been replaced in today’s p

45、roduction shops by a wide variety of automatic lathes such as automatic of single-point tooling for maximum metal removal, and the use of form tools for finish on a par with the fastest processing equipment on the scene

46、today.</p><p>　　Tolerances for the engine lathe depend primarily on the skill of the operator. The design engineer must be careful in using tolerances of an experimental part that has been produced on the en

47、gine lathe by a skilled operator. In redesigning an experimental part for production, economical tolerances should be used.</p><p>　　Turret Lathes Production machining equipment must be evaluated now, m

48、ore than ever before, this criterion for establishing the production qualification of a specific method, the turret lathe merits a high rating. </p><p>　　In designing for low quantities such as 100 or 200 pa

49、rts, it is most economical to use the turret lathe. In achieving the optimum tolerances possible on the turrets lathe, the designer should strive for a minimum of operations.</p><p>　　Automatic Screw Machine

50、s    Generally, automatic screw machines fall into several categories; single-spindle automatics, multiple-spindle automatics and automatic chucking machines. Originally designed for rapid, automatic produ

51、ction of screws and similar threaded parts, the automatic screw machine has long since exceeded   the confines of this narrow field, and today plays a vital role in the mass production of a variety of precision

52、 parts. Quantities play an important part in the economy of th</p><p>　　Automatic Tracer Lathes   Since surface roughness depends greatly on material turned, tooling , and feeds and speeds employed

53、, minimum tolerances that can be held on automatic tracer lathes are not necessarily the most economical tolerances.</p><p>　　In some cases, tolerances of 0.05mm are held in continuous production using but o

54、ne cut . groove width can be held to 0.125mm on some parts. Bores and single-point finishes can be held to 0.0125mm. On high-production runs where maximum output is desirable, a minimum tolerance of 0.125mm is economical

55、 on both diameter and length of turn.</p><p><b>　　車床</b></p><p>　　車床主要是為了進行車外圓、車端面和鏜孔等項工作而設計的機床。車削很少在其他種類的機床上進行，而且任何一種其他機床都不能像車床那樣方便地進行車削加工。由于車床還可以用來鉆孔和鉸孔，車床的多功能性可以使工件在一次安裝中完成幾種加工。因此

56、，在生產中使用的各種車床比任何其他種類的機床都多。</p><p>　　車床的基本部件有：床身、主軸箱組件、尾座組件、溜板組件、絲杠和光杠。</p><p>　　床身是車床的基礎件。它能常是由經過充分正火或時效處理的灰鑄鐵或者球墨鐵制成。它是一個堅固的剛性框架，所有其他基本部件都安裝在床身上。通常在床身上有內外兩組平行的導軌。有些制造廠對全部四條導軌都采用導軌尖朝上的三角形導軌（即山形導軌

57、），而有的制造廠則在一組中或者兩組中都采用一個三角形導軌和一個矩形導軌。導軌要經過精密加工以保證其直線度精度。為了抵抗磨損和擦傷，大多數現代機床的導軌是經過表面淬硬的，但是在操作時還應該小心，以避免損傷導軌。導軌上的任何誤差，常常意味著整個機床的精度遭到破壞。</p><p>　　主軸箱安裝在內側導軌的固定位置上，一般在床身的左端。它提供動力，并可使工件在各種速度下回轉。它基本上由一個安裝在精密軸承中的空心主軸和

58、一系列變速齒輪(類似于卡車變速箱)所組成。通過變速齒輪，主軸可以在許多種轉速下旋轉。大多數車床有8~12種轉速，一般按等比級數排列。而且在現代機床上只需扳動2~4個手柄，就能得到全部轉速。一種正在不斷增長的趨勢是通過電氣的或者機械的裝置進行無級變速。</p><p>　　由于機床的精度在很大程度上取決于主軸，因此，主軸的結構尺寸較大，通常安裝在預緊后的重型圓錐滾子軸承或球軸承中。主軸中有一個貫穿全長的通孔，長棒料

59、可以通過該孔送料。主軸孔的大小是車床的一個重要尺寸，因此當工件必須通過主軸孔供料時，它確定了能夠加工的棒料毛坯的最大尺寸。</p><p>　　尾座組件主要由三部分組成。底板與床身的內側導軌配合，并可以在導軌上作縱向移動。底板上有一個可以使整個尾座組件夾緊在任意位置上的裝置。尾座體安裝在底板上，可以沿某種類型的鍵槽在底板上橫向移動，使尾座能與主軸箱中的主軸對正。尾座的第三個組成部分是尾座套筒。它是一個直徑通常大約

60、在51~76mm（2~3英寸）之間的鋼制空心圓柱體。通過手輪和螺桿，尾座套筒可以在尾座體中縱向移入和移出幾個英寸。 </p><p>　　車床的規格用兩個尺寸表示。第一個稱為車床的床面上最大加工直徑。這是在車床上能夠旋轉的工件的最大直徑。它大約是兩頂尖連線與導軌上最近點之間距離的兩倍。第二個規格尺寸是兩頂尖之間的最大距離。車床床面上最大加工直徑表示在車床上能夠車削的最大工件直徑，而兩頂尖之間的最大距離則表示在兩個

61、頂尖之間能夠安裝的工件的最大長度。</p><p>　　普通車床是生產中最經常使用的車床種類。它們是具有前面所敘的所有那些部件的重載機床，并且除了小刀架之外，全部刀具的運動都有機動進給。它們的規格通常是：車床床面上最大加工直徑為305~610mm（12~24英寸）；但是，床面上最大加工直徑達到1270mm（50英寸）和兩頂尖之間距離達到3658mm的車床也并不少見。這些車床大部分都有切屑盤和一個安裝在內部的冷卻液

62、循環系統。小型的普通車床—車床床面最大加工直徑一般不超過330mm（13英寸）--被設計成臺式車床，其床身安裝在工作臺或柜子上。</p><p>　　雖然普通車床有很多用途，是很有用的機床，但是更換和調整刀具以及測量工件花費很多時間，所以它們不適合在大量生產中應用。通常，它們的實際加工時間少于其總加工時間的30%。此外，需要技術熟練的工人來操作普通車床，這種工人的工資高而且很難雇到。然而，操作工人的大部分時間卻花

63、費在簡單的重復調整和觀察切屑過程上。因此，為了減少或者完全不雇用這類熟練工人，六角車床、螺紋加工車床和其他類型的半自動和自動車床已經很好地研制出來，并已經在生產中得到廣泛應用。</p><p><b>　　2.數字控制</b></p><p>　　先進制造技術中的一個基本的概念是數字控制（NC）。在數控技術出現之前，所有的機床都是由人工操縱和控制的。在與人工控制的機床

64、有關的很多局限性中，操作者的技能大概是最突出的問題。采用人工控制是，產品的質量直接與操作者的技能有關。數字控制代表了從人工控制機床走出來的第一步。</p><p>　　數字控制意味著采用預先錄制的、存儲的符號指令來控制機床和其他制造系統。一個數控技師的工作不是去操縱機床，而是編寫能夠發出機床操縱指令的程序。對于一臺數控機床，其上必須安有一個被稱為閱讀機的界面裝置，用來接受和解譯出編程指令。</p>

65、<p>　　發展數控技術是為了克服人類操作者的局限性，而且它確實完成了這項工作。數字控制的機器比人工操縱的機器精度更高、生產出零件的一致性更好、生產速度更快、而且長期的工藝裝備成本更低。數控技術的發展導致了制造工藝中其他幾項新發明的產生：</p><p>　　電火花加工技術、激光切割、電子束焊接數字控制還使得機床比它們采用有人工操的前輩們的用途更為廣泛。</p><p>　　一臺

66、數控機床可以自動生產很多類的零件，每一個零件都可以有不同的和復雜的加工過程。數控可以使生產廠家承擔那些對于采用人工控制的機床和工藝來說，在經濟上是不劃算的產品生產任務。</p><p>　　同許多先進技術一樣，數控誕生于麻省理工學院的實驗室中。數控這個概念是50年代初在美國空軍的資助下提出來的。在其最初的價段，數控機床可以經濟和有效地進行直線切割。</p><p>　　然而，曲線軌跡成為機

67、床加工的一個問題，在編程時應該采用一系列的水平與豎直的臺階來生成曲線。構成臺階的每一個線段越短，曲線就越光滑。臺階中的每一個線段都必須經過計算。</p><p>　　在這個問題促使下，于1959年誕生了自動編程工具（APT）語言。這是一個專門適用于數控的編程語言，使用類似于英語的語句來定義零件的幾何形狀，描述切削刀具的形狀和規定必要的運動。APT語言的研究和發展是在數控技術進一步發展過程中的一大進步。最初的數控系

68、統下今天應用的數控系統是有很大差別的。在那時的機床中，只有硬線邏輯電路。指令程序?qū)懺诖┛准垘希ㄋ髞肀凰芰蠋〈捎脦ч喿x機將寫在紙帶或磁帶上的指令給機器翻譯出來。所有這些共同構成了機床數字控制方面的巨大進步。然而，在數控發展的這個階段中還存在著許多問題。 </p><p>　　一個主要問題是穿孔紙帶的易損壞性。在機械加工過程中，載有編程指令信息的紙帶斷裂和被撕壞是常見的事情。在機床上每加工一個零件，都需

69、要將載有編程指令的紙帶放入閱讀機中重新運行一次。因此，這個問題變得很嚴重。如果需要制造100個某種零件，則應該將紙帶分別通過閱讀機100次。易損壞的紙帶顯然不能承受嚴配的車間環境和這種重復使用。</p><p>　　這就導致了一種專門的塑料磁帶的研制。在紙帶上通過采用一系列的小孔來載有編程指令，而在塑料帶上通過采用一系列的磁點瞇載有編程指令。塑料帶的強度比紙帶的強度要高很多，這就可以解決常見的撕壞和斷裂問題。然而

70、，它仍然存在著兩個問題。</p><p>　　其中最重要的一個問題是，對輸入到帶中指令進行修改是非常困難的，或者是根本不可能的。即使對指令程序進行最微小的調整，也必須中斷加工，制作一條新帶。而且?guī)ㄟ^閱讀機的次數還必須與需要加工的零件的個數相同。幸運的是，計算機技術的實際應用很快解決了數控技術中與穿孔紙帶和塑料帶有關的問題。</p><p>　　在形成了直接數字控制（DNC）這個概念之后，

71、可以不再采用紙帶或塑料帶作為編程指令的載體，這樣就解決了與之有關的問題。在直接數字控制中，幾臺機床通過數據傳輸線路聯接到一臺主計算機上。操縱這些機床所需要的程序都存儲在這臺主計算機中。當需要時，通過數據傳輸線路提供給每臺機床。直接數字控制是在穿孔紙帶和塑料帶基礎上的一大進步。然而，它敢有著同其他信賴于主計算機技術一樣的局限性。當主計算機出現故障時，由其控制的所有機床都將停止工作。這個問題促使了計算機數字控制技術的產生。</p>

72、;<p>　　微處理器的發展為可編程邏輯控制器和微型計算機的發展做好了準備。這兩種技術為計算機數控（CNC）的發打下了基礎。采用CNC技術后，每臺機床上都有一個可編程邏輯控制器或者微機對其進行數字控制。這可以使得程序被輸入和存儲在每臺機床內部。它還可以在機床以外編制程序，并將其下載到每臺機床中。計算機數控解決了主計算機發生故障所帶來的問題，但是它產生了另一個被稱為數據管理的問題。同一個程序可能要分別裝入十個相互之間沒有通訊

73、聯系的微機中。這個問題目前正在解決之中，它是通過采用局部區域網絡將各個微機聯接起來，以得于更好地進行數據管理。</p><p><b>　　3.車削加工</b></p><p>　　普通車床作為最早的金屬切削機床的一種，目前仍然有許多有用的和為人要的特性和為人們所需的特性。現在，這些機床主要用在規模較小的工廠中，進行小批量的生產，而不是進行大批量的和產。</p&

74、gt;<p>　　在現代的生產車間中，普通車床已經被種類繁多的自動車床所取代，諸如自動仿形車床，六角車床和自動螺絲車床?，F(xiàn)在，設計人員已經熟知先利用單刃刀具去除大量的金屬余量，然后利用成型刀具獲得表面光潔度和精度這種加工方法的優點。這種加工方法的生產速度與現在工廠中使用的最快的加工設備的速度相等。</p><p>　　普通車床的加偏差主要信賴于操作者的技術熟練程度。設計工程師應該認真地確定由熟練工人

75、在普通車床上加工的試驗件的公差。在把試驗伯重新設計為生產零件時，應該選用經濟的公差。</p><p>　　六角車床 對生產加工設備來說，目前比過去更注重評價其是否具有精確的和快速的重復加工能力。應用這個標準來評價具體的加工方法，六角車床可以獲得較高的質量評定。</p><p>　　在為小批量的零件（100~200件）設計加工方法時，采用六角車床是最經濟的。為了在六角車床上獲得盡可能小的公差

76、值，設計人員應該盡量將加工工序的數目減至最少。 </p><p>　　自動螺絲車床自動螺絲車床通被分為以下幾種類型：單軸自動、多軸自動和自動夾緊車床。自動螺絲車床最初是被用來對螺釘和類似的帶有螺紋的零件進行自動化和快速加工的。但是，這種車床的用途早就超過了這個狹窄的范圍?，F(xiàn)在，它在許多種類的精密零件的大批量生產中起著重要的作用。工件的數量對采用自動螺絲車床所加工的零件的經濟性有較大的影響。如果工件的數量少于100

77、0件，在六角車床上進行加工比在自動螺絲車床上加工要經濟得多。如果計算出最小經濟批量，并且針對工件批量正確地選擇機床，就會降低零件的加工成本。</p><p>　　自動仿形車床因為零件的表面粗糙度在很大程度上取決于工件材料、刀具、進給量和切削速度，采用自動仿形車床加工所得到的最小公差一定是最經濟的公差。</p><p>　　在某些情況下，在連續生產過程中，只進行一次切削加工時的公差可以達到0